• 목록
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

The change of your door lock is an easy and inexpensive method to increase the security of your home. The process is not for everyone. It requires a certain amount of skill and perseverance.

The cylinder is located within the knob body. The cylinder is responsible for recognizing the key as it is inserted into the lock.

Removal of the old lock

The first step in replacing the door lock is to get rid of the old one. This is a relatively simple process, but there are a few points to be aware of. Make sure your new lock fits the door. This will ensure that it fits properly and does not leave a gap in the latch or deadbolt plug.

After you have removed the latch plate, look for two bolts or screws on the inside of the casing, which connect the casing and halves of the lock. Remove these screws using a screwdriver before removing the lock out of the door. If you have a mortise locking mechanism, there is a set screw that holds the handle to the spindle. Take off the doorknobs by removing this screw with the help of a screwdriver.

Remove the deadbolt as well as the latch plug from the door jamb. Install the new lock. If you are replacing a mortise lock, you must also measure the distance between the lock case and the edge of your door to ensure that the new lock will be able to fit.

You might want to change your lock for a variety reasons, for instance, if you suspect that someone else holds the key or you've got an incoming roommate. In any event, you could save money by taking the lock off yourself rather than paying a professional to do it. The process is simpler than most people think, and it can be completed in just a few minutes.

Remove the trim and handle of your door. Then, pull the trim loose using a screwdriver that is flat. You will be able twist off most of it, and in some instances the handles may fall off entirely. Then, check the handle for a tiny pinhole on the inside. Then insert a straightened paper clip into it. This will activate the release mechanism, allowing you to take off the handle. Then, look on the interior side of the lock to find a small tab and press it with a flat screwdriver. Once the spindle is removed, you can take off the cylinder and housing.

Selecting a new locking system

When it comes to selecting a new lock there are a lot of options. Take a look at the various types of locks and select one that matches the design of your door. Consider the backset, which is the distance between the edge and the center of lock hole. Also, think about the cross bore, a tiny hole that is located at the edge of your door frame. Select a lock that will fit the door's thickness and the swing.

Most door replacement window locks have been evaluated by BHMA and the American National Standards Institute to give you an idea of how well they stand up to use and how difficult they are to disable or pick. A grade 3 lock could be ideal for a quiet rural apartment complex, while an entry grade lock could hold up better to the traffic near a busy store front on a city street.

Most smart door locks need a digital code to open. If you are concerned about hacking, or any other security concerns, consult an expert locksmith.

Replacing the cylinder

If your door lock's cylinder is damaged or broken you can repair replacement upvc window locks lock, read page, it in a matter of minutes by completing a do-it-yourself project. The key is to choose the right cylinder, and follow the instructions that come with it. The first step is to take off the knob or handle, should there be one and then remove the trim around the base of the double glazing window lock repair cylinder with the help of a screwdriver. Once the trim has been removed, you can remove the screws holding the cylinder with the flathead. The cylinder is then gently pulled out of the door.

Before installing the new cylinder, make sure it's the right length for your door. With a tape measure, measure the distance between the center of the cylinder and the left and right side. Buy a new cylinder that has the same measurements. This will stop cylinders from snapping when the door is hit or the key is stuck inside.

Install the replacement upvc window locks cylinder into the door and then turn the key. This will ensure that the cylinder is in alignment with the carrier, which is usually located on the outside of the lock. After that, you can loosen the set screw that is supposed to be a couple of turns in the head. If there is a screw at the exterior of the case that holds the door, you will have to loosen it.

After removing the lock cylinder, you can replace upvc window lock it with the new lock by slipping the new cylinder into the case and tightening the set screw. It is also recommended to reinstall the part that connects the cylinder to the lock indicator stem that you can do by removing three small tabs on the back of the cylinder with needle-nose pliers. Then, you can attach the smaller bracket to the back of the cylinder. You should then reinstall the strike plate and latch plate, along with the retaining rings fixed to the top of the lock cylinder.

Installing a new lock

If you're replacing a previous lock, you should start by measuring the width of your door. The majority of residential locksets come with a thickness of 3/8 to 1 3/4 inches. If your door is more thick you will require a thick door kit that includes longer screws, a longer tail piece (for door knobs) or spindle extension (for deadbolts).

Most locks come equipped with a comprehensive installation guide to aid you. Read the instructions carefully before starting the process to ensure that you are following all the steps. The manual will give you a clear idea of the level of skill that is required to complete the task. If you're changing locks for the first time, you might want to ask an experienced friend for assistance.

It's a great idea to tape the openings in the old hardware before installing the new lock. This will prevent the screws from slipping out of the holes, and will protect any tile you might have put in the area. It also helps prevent potential damage from rust grime, dirt and. SECURAM Touch includes an ad-hoc strip of masking tape or gaffer tape, however you can use any tape you have.

After you have removed the screws that hold the lock's inner half to the exterior and take the lock off immediately. It's important to do this swiftly to prevent the lock from accidentally closing on itself and harming the mechanism.

If your new lock is equipped with an latch bolt, install the new bolt into its upper cross bore. Make sure to place it in the right position, which is indicated by an arrow. Next, fit the latch plate over the bolt and secure it in the correct position.

Finally, screw the deadbolt and strike plates to the door jamb. Test the deadbolt by throwing it a several times to make sure that it extends all the way into the strike plate and is completely secure. Follow the steps that come with your electronic smart lock to program it. This involves downloading an application, entering your email address, verifying your identity, then accessing the wireless network to add your device.