• 목록
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat doblo key programming 500 Key Fob Won't Work

A key fob with the Fiat 500 remote key programming 500 number is a convenient way to open the doors and begin the car. However, there are many reasons why the fob won't be working. This includes a dead battery, water damage, receiver modules issues, and interference.

This listing is for a NEW replacement fiat remote key replacement Flip Key Remote that is similar to the Ilco brand. It must be professionally programmed (click here to find local locksmiths in the automotive industry). This remote includes trunk, lock and unlock buttons.

Dead Coin Battery

A dead battery is the most common cause of your 500 key fob that isn't working. Modern key fobs come with a limited operating range and must be within some feet of the vehicle in order to function. If you are further away from your vehicle and hit the keyfob, it will not respond, and display the message "Key Fob Not Detected".

If this occurs If this happens, replace the battery in the coin-cell (Part Number CR2032) by a fresh one of a reputable brand such as Panasonic Duracell or Energizer. They are available at the local hardware store or online.

You can test the battery on your coin-cell by pressing the buttons while standing close to your fiat 500 spare key cut fiat 500 key cutting. The parking lights should blink and the key fob should operate the lock and unlock switches.

If your key fob doesn't work even after replacing the battery, it may be water damage that prevents it from connecting to the module in your vehicle. Water damage can happen in a number of ways, ranging from a light splash to submerging the fob salt water at the beach. If you suspect that your fob has been exposed to water, put it in a bag of rice to draw out the moisture. If this does not work, you'll need to have the fob reprogrammed either by an auto locksmith or a dealer.

Water Damage

Water damage can occur when you submerge the fob in the ocean, or wash it in a machine. Saltwater can cause the circuit board to short and eventually fail. It's not a good thing to submerge the fob in water however, but don't give it up when you accidentally drop it in water, or fail to remove it from your pants pocket.

First take the battery off the fob. Clean the electronic chip using isopropyl or a similar product and dry it completely before replacing the battery. Then, test the fob to verify if it is working. If the key does not function then it might need to be reset. This is usually handled by an auto locksmith or dealer.

If the key you have is older and not programmed to work with your vehicle then you'll need to replace it completely. A professional automotive locksmith will be able to complete this process. The locksmith will have to cut the key to match the ignition in your vehicle. They'll also need to reprogram the fob in your vehicle's system. This is a fast and affordable process which can be completed in the next day.

Receiver Module Issues

One of the most common reasons why your 500 key fob may stop functioning is that it's out of range. The remote typically has 30 feet of range or less, and if it's too far from your fiat car key replacement, it won't respond to your commands. It's easy to fix this by moving the remote closer to your car until it responds.

If you've replaced the coin battery (commonly called a "button" or "watch") and the fob isn't working It could be because of an internal circuit board issue. Reprogramming your fob can resolve this issue. You can find directions on how to do this for most vehicles by searching YouTube or consulting the owner's manual.

It's possible that you need to replace the metal clips that hold the battery of your coin in place. If they lose tension, they could stop the battery from being properly seated and cause your remote to malfunction.

In rare cases the fob can become out of the vehicle's sync because of hardware or software problems. This can be a major issue, but you are able to often fix this by visiting a local dealer or auto locksmith to reprogram your fob for you. In certain instances the software might need to be reinstalled in your body control modules.

Interference

Interference can also cause the key fob to not receive or transmit the signal. This could happen if the key fob is near radio transmitters (cell phones, radar detectors) or another source of electromagnetic radiation. Other reasons the key fob may not function could be due to a weak connection to the buttons, damage to the internal chip or water damage.

If the key fob suddenly stopped working, in the middle of the night and you've tried everything you can at home to fix it e.g. replacing batteries, reprogramming or using the spare key fob, you may have a defective receiver module on your 500. The receiver module, which is located beneath the dashboard, receives radio frequency signals from your key fob. It converts them to electronic commands that the vehicle interprets.

Luckily, there is an easy method of resetting every single system on board in your 500 and include the key fob. Disconnect the battery for 15 minutes, removing first the negative cable and then the positive cable. Then reconnect the battery. This will clear out any remaining electricity and then restart the car's computers. This could allow you to the key fob to function again. If the issue continues, you should consult a certified technician. They will be able to identify the root of any issues.