• 목록
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Change of the door lock is a quick and cheap way to improve your home security. The process is not for all. It requires some skill and perseverance.

You must replace the cylinder, which is located within the knob's body. The cylinder is responsible to recognize the key when it is inserted in the lock.

Take off the lock that was previously used.

The first step in replacing the door lock is to take out the old lock. It's a straightforward process, however you should keep some things in mind. Make sure your new lock fits your door. This will ensure it is secure and doesn't leave a gap in the latch or deadbolt.

After removing the latch plate, you will need to look for two bolts or screws in the casing's interior that are holding the casing together with the two halves of the lock. Remove these screws with the help of a screwdriver, and then remove the lock out of the door. If you have a mortise locking, there might be a set screw located at the base of the handle that holds it to the spindle. Take off the doorknobs by removing the screw using a screwdriver.

Take the deadbolt and latch plug from the door jamb. Install your new lock. If you are replacing a mortise lock you should also measure the distance between the lock case and the edge of your door to ensure that the new lock will fit.

It is possible to replace your lock for a variety of reasons, including the possibility that someone else is holding the key or if you've an incoming roommate. You can save money if you take the lock off yourself instead of paying for a professional. The process is simpler than many people imagine, and it can be completed in a few minutes.

Remove the trim and handle of your door. Then, pull the trim loose using a flat screwdriver. You will be able to pull off the majority of it and in certain cases the handles could come off completely. Next, examine the handle for a tiny pinhole on the interior side and insert a straightened clip into it. This will activate the release mechanism and allow you to remove the handle from the door. The next step is to look at the interior side of the broken window lock repair for another small tab that you can press with a flat screwdriver. Once the spindle has been removed, you can then take off the cylinder and housing.

Making a choice for a new lock

When it comes time to pick a new lock, you have many choices. Think about the various kinds of locks and pick one that is in keeping with the design of your door. Consider the backset which is the distance between the edge and the center of the hole in the lock. Also, think about the cross bore, a small hole in the middle of your door frame. Select a lock that will fit the door thickness and the swing.

The American National Standards Institute and BHMA have graded all locks for doors to give you an idea of their durability and the difficulty to pick them or disable them. A lock grade 3 might be ideal for a peaceful apartment in the country, while replacement upvc window locks that are grade 1 might be better suited to a busy street near a storefront.

Most smart door locks require a digital code to open. If you're worried about hacking or other security concerns seek out an expert locksmith or your local police department for advice.

Replace the cylinder

It is easy to replace a damaged or broken window lock repair door lock cylinder with an easy DIY project. It is crucial to choose the appropriate cylinder and follow all instructions. The first step is to remove the knob or handle should there be one and then remove the trim around the base of the lock cylinder using a screwdriver. Once the trim has been removed, it is possible to remove the screws that hold the cylinder with a flathead. The cylinder is then gently removed from the door.

Before installing the new cylinder, make sure that it is the right length for your door. Measure the distance from the center to the left and right sides of the cylinder with the aid of a tape measure. Buy a new cylinder that has the same measurements. This will prevent the cylinder from snapping, which could happen when the door is kicked out or when the key gets stuck inside.

Place the Replacement locks for double glazed windows cylinder inside the door, and then turn the key. This will align the cylinder with the carrier which is typically on the outside of your lock. Then, loosen the set screws that should be only a couple of turns into the head. If there is a screw at the edge of the case, which holds the door, you'll have to loosen it.

After removing the lock cylinder after which you can replace it with the new lock by slipping the new cylinder into the case and tightening the set screw. The process of reinstalling the component that connects a cylinder to the stem of a lock indicator is also crucial. It is done by pulling three small tabs on the back of the cylindrical using needle-nosed pliers. Attach the smaller bracket to the cylinder's back. Then, you must put back in the strike plate and latch plate, as well as the retaining ring connected to the top of the lock the cylinder.

Installing the new lock

Begin by measuring the door's width if you are replacing an existing lock. Most locksets for residential use have a thickness of 3/8 to 1 3/4 inches. If your door is more thick you will require an extra-thick door kit that includes longer screws and a longer tail piece (for door knobs) or spindle extensions (for deadbolts).

Most double glazing window locks repairs come with a detailed installation guide to help you. Before beginning, you must read the instructions to make sure you have followed all the steps. The manual will give you an idea of how much skill is required to complete the task. You may want to ask a friend who has experience changing locks for assistance if are changing a lock the first time.

Before installing the new lock, it's a good idea to cover the openings with tape the old hardware. This will prevent the screws from falling through the holes, and also protect any tiles you have installed. It also helps prevent potential damage from rust grime, dirt and. SECURAM Touch comes with a strip painter's tape designed to be used for this purpose, however you can also use gaffer's tape or masking tape when you have it.

After removing the screws that hold the lock's interior half to the exterior and remove the lock immediately. It is important to do this quickly to prevent the lock from accidentally closing and damaging the mechanism.

If your new lock is equipped with an internal latch bolt, insert the new bolt into its upper cross bore. Make sure you put it in the proper location, which is marked by an arrow. Then, slide the latch plate onto the bolt and screw it into place.

Finally, screw the deadbolt and strike plates to the door jamb. Test the deadbolt by throwing it a several times to make sure that it is extended all the way through the strike plate and is fully secure. If you're using an electronic smart lock, be sure to follow the included instructions to program it. This involves downloading an application and registering your email address, verifying you identity, and connecting to the wireless network to connect your device.